FSAE RULES 2012 PDF

Formula Student Electric Rules Brake Over-Travel Switch (Specific FSG change of Formula SAE® Rule B ). ARTICLE 1: FORMULA STUDENT OVERVIEW AND COMPETITION – as article 1 from FSAE Rules except. Formula Student permits students to compete. SAE International. All Rights Reserved. Formula SAE Rules revision. Formula SAE® Rules. Table of Contents.

Author: Fesar Tausho
Country: Lesotho
Language: English (Spanish)
Genre: Marketing
Published (Last): 26 August 2007
Pages: 326
PDF File Size: 14.72 Mb
ePub File Size: 17.78 Mb
ISBN: 772-2-97476-841-3
Downloads: 46668
Price: Free* [*Free Regsitration Required]
Uploader: Voodoomi

This may be difficult as the tube is allowed to be integrated into the laminate but there is often a contour that comes from the tube that is visible. No undertrays behind rear tire No wings over rear tire.

To maintain the equivalent yield and ultimate tensile strength the same cross-sectional area of steel as the baseline tubing specified in T3. Due Date — SESs must be fse no later than the date indicated on the competition website.

Round, mild or alloy, steel tubing minimum 0. Zach Moorhead Sooner Racing. Correct, Lithium Iron Phosphate. Once you have selected the link, the registration page will appear.

If the IA plate is bolted to the Front Bulkhead, it must be the same size as the outside dimensions of the Front Bulkhead. The Structural Equivalency must address each of the items below. The Rules Committee will respond as quickly as possible, however responses to questions presenting new issues, or of unusual complexity, may take more than two weeks.

  ELECTROANATOMICAL MAPPING AN ATLAS FOR CLINICIANS PDF

Section EV is largely based on the rules for the electric classes at Formula Student UK and Formula Student Germany with modifications implemented following a review by an international group of electric engineering experts. No fore and aft translation of the template will be permitted during insertion.

Node-to-node triangulation — An arrangement of frame members projected onto a plane, where a co-planar load applied in any direction, at any node, results in only tensile or compressive forces in the frame members.

The challenge to the design team is to develop a prototype car that best meets the FSAE vehicle design goals and which can be profitably marketed.

Shipments must be sent with the sending team or university listed as the receiving party. Teams may not protest rule interpretations or actions that have not caused them any substantive damage.

FSAE Rules Published

The test facility may be part of the University but must be be supervised by professional staff or University faculty. Refer to the Rule C5. This distance shall be measured horizontally, on the vehicle centerline, from the rear surface of rues Front Hoop to the forward most surface of the steering wheel rim with the steering in the straight-ahead position.

A student at any University making up the sfae may compete at any event where the team participates.

РЕГЛАМЕНТ англ

The following requirements and restrictions will be enforced through technical inspection. Exhaust System Exhaust manifold insulation wrap. Tech Sheet pg1 shown Each team receives these forms 4 pgs at registration, and will bring them to you.

  KANKER TUBA FALOPI PDF

A team found to be improperly presenting any evidence of the manufacturing process will be barred from competing with a monocoque through at least the following year. The shoulder harness must be the over-the-shoulder type. For example, if a rrules specifies a minimum dimension for a part the Committee will not answer questions asking if a smaller dimension can be used. All students, both domestic and international, must affiliate themselves online or submit the International Student Registration form by January 31 of the year of the competition.

2015 FSAE Rules students.sae.org /cds/formulaseries/rules/ Format

Only separate shoulder straps are permitted i. Rupes the first month of registration any untaken slots at any of the competitions will be available to any team on a first come, first serve basis. This introduction only summarizes parts of the rules the revised text and do not change or replace the rules.

The vehicle must be open-wheeled and open-cockpit a formula style body with four 4 wheels that fsaae not in a straight line. To maintain EI with a thinner wall thickness than specified in T3. Frame Member – A minimum representative single piece of uncut, continuous tubing.

An electronic question submission system is being developed for the North American competitions.