Find the user manual and the help you need for the products you own at ManualsOnline. I got an old laptop model MA2 without powersupply. SetIP command to see and change the IP addresses of the console. This command can be used to change both Ethernet connectors and even set a gateway. Requirement: STP (shielded twisted pair) cable with RJ45 connector, min. Cat 5e . To connect Ethernet port 1: Connect one end of an Ethernet cable to the.
|Published (Last):||8 May 2004|
|PDF File Size:||17.46 Mb|
|ePub File Size:||1.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
So with the DC Power connected, see if there is power on the back of the jack, Or on the two legs of the diode shown in the second picture. Im wondering if it would help just in case. The host skipped out, and I lost mabual domain in the process. Check with another battery. Each console have two IP addresses – one for each Ethernet connector on the back.
Gateway Laptop MA2 User’s manual |
Hi, I have a gateway MA7 Series laptop that constantly reboots about every 3 seconds, have swapped batteries, swapped ram and remove all drives and hard drive, and and it is still in a rebooting loop Ray. There are three ways to set the IP gteway in the console. Hoosier Newman Wed May 22, Neil Wed Jun 30, Jumper a thin wire from back of DC jack to maual pair of legs on the diode [PD33] then give it a try turning it on. Posted by Hoosier Newman at 9: Further testing is necessary.
If I unplug te battery, the computer won’t start with just the power cord. Hey Mayo, Just found this post. It looks like it marked P1 or P As to this point. I have a Mznual that arrived just the other day same issue. I have a MA3 with a similar problem.
The pictures show what the diode looks like and how I bypassed it on one unit. Jamerton Dec 20, Then all the copper may be gone, and is a real ‘dog’ repair or is beyond repair. The motherboard is slightly different than the Vateway you describe here.
Gateway Official Site: Worldwide
The AC plug would require much wobbling and pinning in a specific location to allow the unit to run. Maleko48 Dec 10, Since working with so many models, I cannot keep each one in my head, as well as my other projects that are totally unrelated running out of room in my head. AC power plugged in, battery in, and the power button does nothing. On the bottom of the motherboard there are two identical chips marked AO side by side. Do you know the number on the chip or replacement so i can order.
Update Me Mon Feb 14, The substrate was about the size of an pencil eraser, and from there we had to add a custom chip, SMT caps, resistors and 12 gold filament wires. I have resistance on the POS pin to the shield of the dc port. No you should not, if the replacement supply doesn’t hum, it means that yours is going bad, unless it was not the same type or voltage.
Check with meter in Diode or Resistance. Blacky Dec 14, Maybe these missing capacitor s took out part of the charging circuit? Check the front center of the DC to the rear for continuity. I would also like to know if I Could connect the power adapter directly to the motherboard’s pos and neg.
I grabbed another power cord working just fine. Mayo Hardware Sun Jan 02, My question is how on earth manhal you solder a jumper to a solder joint that’s the size of a pin head on gatway diode?
Glad to hear you got your problem solved!!!! Windows OS and Software.
Now it won’t even do that so the customer brought it in. I was hopeing you have some info for me on a similar symptom on a dell d How do you test them if so? Good to see that you never gave up. Anonymous Mon Apr 26, Will check into a MA3 tomorrow, and see what tip I can provide.
I’ll attempt to re-create the same test here. Hoosier, It will be sometime till I can test the battery out. The only way it works now is if a external monitor is plugged in. I may have poseted previous comment on wrong page. They should do either to solve the problem.
Labor and Postage is more than the same item on eBay. No, create an account now. David Thu Oct 21,