Smith Meter® AccuLoad and AccuLoad III are trademarks of FMC The default or operating values used in this manual and in the program of the AccuLoad III. AccuLoad III High Speed Prover Output · AccuLoad III Vapor Recovery Application Bulletin · AccuLoad IIInet Application Manual · AccuLoad III-S N4 Hardware. The default or operating values used in this manual and in the program of the Smith Table of Contents iii. Volume Accuracy – Preset Amount Type.

Author: Grom Zulkizuru
Country: Nicaragua
Language: English (Spanish)
Genre: Career
Published (Last): 5 July 2012
Pages: 491
PDF File Size: 1.36 Mb
ePub File Size: 18.6 Mb
ISBN: 515-6-23623-977-9
Downloads: 40536
Price: Free* [*Free Regsitration Required]
Uploader: Voodoojinn

This is most commonly done with products that mix very easily. For more information on these functions and others, please refer to the ProNet User s Manual.

The following More information. System Program Code determines the period during which the AccuLoad remains in a full screen format. If the STOP button is pressed during flow, and if the Start after Stop delay is programmed, the preset position will display: The chart below illustrates the keystrokes that move between states, depending on the starting screen.

The AccuLoad III is also capable of maintaining back pressure on the measurement system using either automatic flow optimization or a pressure transmitter. An alarm will be set if the number of errors exceeds the programmable maximum.

Smith Meter AccuLoad III – PDF

These jumper states are available via communications. Type the abstract of the document here. This script will walk you through the basic process of setting up the remote access, data logging, FTP file More information.


The AccuLoad III allows any combination of ratio blending arms to be supported with the available meter inputs. The card reader interface is activated by choosing the card reader option in the serial communications function program code.

Start display at page:. Note acculoae the most recent value for this entry will be displayed.

This will have the same effect as if the additive output was stopped at the end of the batch. The ready state for triple arm operation initially consists of a split screen accuolad the top display for Load Arms 1 and 3, and a full screen on the bottom display for Load Arm 2.

Smith Meter AccuLoad III

This new injector type is similar to a metered injector type in that a meter pulse input is received; however, rather than a solenoid, a digital valve is used to control the flow of the additive. Safety and volume accuracy functions including acculoax high flow, low flow, overrun, and temperature probe failure are also monitored per their program parameters.

Should flow rate variations occur, the profile is dynamically adjusted to attain the best possible mix. With Smart or metered injectors, the additive volume injected is actually measured, providing the ultimate in feedback.

Accuload iii manual español – Google Docs

If both load arms were at the preset screen, then the START key begins the batch on the arm that maanual the focus last. Flow rates are adjusted for optimal blend accuracy while conforming to the programmed system flow profile using Smith s exclusive control algorithm.

Integrated Control Technology More information. To initiate the proving sequence, the AccuLoad will prompt for the prover manuaal of cubical expansion. Two programmable alarm contacts are available.


404 page not found

However, as a precau. AccuLoad III acculoadd available in an explosion-proof housing for hazardous locations. Note that only those factors currently programmed will be offered as selections. Side-stream blending is two-product ratio blending where the minor of the two products is metered and is controlled by a valve.

If the programmed message is too long for the viewport, it is wrapped to the next line. Another meter and control valve is located downstream from where the two products merge.

The AccuLoad III, if so programmed, will automatically calculate and adjust the additive pulse output to be stopped at the first trip point manuaal the product with the same number of pulses. Enter text from picture: It describes how to configure the required WiFi and. In split screen mode, load arms 1 and 2 appear side by side, with a black border around the active view. To perform Ethernet setup and communication verification, first perform Acculoda setup and communication verification: You can access these features by selecting the items under More information.

Volumetric correction is calculated directly from published API equations providing precise volumetric measurement results.

The table above indicates default operation. The ratio product s can be plumbed either upstream or down stream of the sequential product meter. It is configurable to support a variety of user applications.